What is radiant barrier?
The name comes from the ability to be a barrier to the transfer of radiant heat. Radiant barrier is made from materials that are very good at reflecting radiant heat and they also are very poor at emitting radiant heat.

What is radiant heat?
Radiant heat is heat that is radiated from a heat source through space (with or without air). The heat you feel from a hot garage door or the roof of your car is radiant heat. Most of the heat from a bright light bulb is radiant heat. Radiant heat is also called infra-red heat or infra-red energy.

What is infra-red energy?
Infra-red energy is electro-magnetic energy that is not visible. It is next to red in the wavelength spectrum. It travels at the speed of light until it hits an object. When infra-red energy is travelling through air, a very small portion of the energy is absorbed by molecules in the air.

How does heat move?
Heat moves by conduction, convection, and radiation.
Conduction is the process that occurs in substances denser than air like water and wood and stone where the heat moves through the substance. Conduction occurs rapidly in metals like gold and copper and very slowly through less dense products like fiberglass insulation.
Convection is the process where air makes contact with substances that are conducting heat and the air is heated. Hot air rises and this movement makes room for cooler air and the process continues until the air and the surfaces are close to the same temperature
Radiation is the process of the infra-red energy emitting from the heated substance through space. The energy travels in a straight line at the speed of light until it is absorbed or reflected by another substance. It is important to remember that in order for heat to move by radiation, there must be space between the objects. The space can be as small as a few air molecules and still be effective. If the objects are touching, then the heat moves by conduction, not  radiation.

What is reflectivity?
Reflectivity, for radiant barrier purposes, can be defined as a measure of how much of the energy is reflected and not absorbed by the barrier. Very shiny aluminized flims can reflect as much as 98% (gold) of the radiant heat that strikes it . 

What is absorbtivity? Absorbtivity, for radiant barrier purposes, can be defined as a measure of how much of the energy is not reflected and is absorbed by the material.

What is emissivity?
Emissivity is the ability for radiant heat to emit from a surface.  The higher the emissivity, the faster radiant heat is emitted.  . Very shiny aluminized film only emits about 3% of the heat absorbed radiantly and also from the hot air around it.  Paint (any color), emits at .94, concrete, block and brick at .94 while a chromed surface emits at .05.  This is why pot belly stove are flat black, so they will freely emit radiant heat. For comparison, unpainted wood has an e value of .95 making it an excellent emitter (that's why insulation gets so hot). Polished gold (the lowest e value), has an e factor of .02 and be seen on the face shields of space helmets.

What kind of materials are used to make radiant barrier?
Aluminum foils are one common material. Our proprietary products use a new type of plastic radiant barrier made possible by successful research into making a lighter weight radiant barrier for spacecraft. The process is called vacuum deposition technology and it makes it possible to put a very, very thin deposit of aluminum on a film substrate.

Where is the hottest place in the attic?
Most people (architects, builders even engineers), quickly comment that the hottest place in the attic is up near the center of the roof.  Heat rises right?  Sure, heat rises but radiant travels at 186,000 miles per second in a straight line from the emitting source.   For this example (since we are talking about houses), it would be the roof deck.  So, if radiant heat is being emitted from the roof deck towards the insulation where does it stop?  The insulation.  Care to venture a guess now where the hottest spot is in the attic?
The top couple of inches of the insulation!  Fact is, 1" below the insulation can be as much as 20 to 30 degrees hotter than the hottest air you can measure anywhere in the attic...including up near the peak.  And it remains the hottest entity in the attic until late into the evening.  Your A/C system must work overtime not only to overcome the outside heat, but this stored heat just above your ceiling.  It is easy to comprehend when we consider that the insulation has been absorbing radiant heat all day long, and now it is resisting that heat is trying to leave into the cooler attic air.  Keep in mind all fibrous insulation has a resistance to heat flow while RBS products change the direction of heat.

In the attic, where is the best place to install radiant barrier?
One problematic technique is to put radiant barrier directly on the underside of the roof sheeting. What happens in any attic that is not extremely well ventilated is that the surface of the radiant barrier gets very hot and the heat is conducted and convected into the air of the attic causing the attic and its insulation to get quite hot. Then once the sun goes down and the heat wants to radiate out of the insulation, it is reflected back by the radiant barrier trapping this unwanted heat for hours. To see the results of this type of application, click here.
A better technique but not without its technical challenges is to attach the radiant barrier to the bottom of the roof rafters, the structural members that support the roof sheeting. This creates a chase between the sheeting, the rafters on each side and the radiant barrier. This chase can be used to provide a thermal chimney where cooler air can be drawn in at the bottom, preferably from the outdoors and not from the attic, and then this air is warmed and it rises and exits to the outdoors at a ridge vent at the top of the attic. Without this controlled ventilation technique, the result of putting radiant barrier at the bottom of the rafters would be the same as applying it directly to the sheeting. Obviously, this controlled ventilation technique needed is also not practical to retrofit to existing homes.  Further, any application of radiant barrier up at the roof deck has little or no savings or impact on comfort during winter months.  Airborne dust moving with the vented air up this chase is going to be deposited on the reflective surface more rapidly than a single layer over the insulation.  One other consideration is the overheating of shingles.  Shingle manufacturers are now limiting or voiding warranties where RBS is installed under the roof decking.

So, the only logical location left is on top of the insulation.  Here, the radiant barrier does the bulk of its work by preventing the infra-red energy from being absorbed by the attic insulation.  Laying it out flat will collect dust.  This is why the RBS Chips are patented.  Only the RBS Chips save you energy everyday of the year and carries a lifetime performance warranty...dust or no dust....forvever.

How important is attic ventilation with an attic radiant barrier system?
Ventilation is very important because this is the primary method used to get rid of the heat that is being stopped by the radiant barrier. In climates that require a lot of cooling, it is recommended that attic ventilation at the top of the attic meet or exceed the Uniform Building Code recommendations of 1/150th of the attic area. The UBC also specifies 1/600th at the eaves/soffits of the roof. It is recommended that this be at least 1/200th of the attic area. The UBC's attic ventilation requirements are directed toward preventing moisture condensation problems but they are equally valuable to hot climate homes that need to get rid of the heat absorbed by the roof.  Fifteen years of studying homes and attic ventilation has shown the above UBC values fall far short of what better performance dictates.   A formula of 10 square feet of venting per thousand square feet of attic area has shown beneficial reduction of attic temperature and moisture removal.  50% of this venting is best located around the perimeter in the soffets and the other 50% at the peak of the roof.  Two gable vents are simply not enough
 Remember, the UBC code is the minimum requirements.     Visting our venting page by clicking here.

Isn't it difficult to install radiant barrier in an existing attic?
Sheets of radiant barrier are very difficult to install in existing attics. It is also difficult to get a good installation because of the difficult working conditions of extreme heat in the summer, low headroom, numerous roof framing or truss webs in the way, nails sticking you in the head,  and low light conditions.

What is the "Achilles Heel" of radiant barrier?
Yes.  One most know one's strengths and one's weaknesses! Think about this. What makes a mirror not reflect well? Dirt! It is the same for radiant barrier so when dust collects on the upward-facing highly reflective surface of the radiant barrier, it then has a very low reflectivity and is now a very good absorber. Now only the downward-facing low emissivity surface is left to do the work.  One of our competitors has this on thier web page:

Q. What about using "foil chips" in my attic ? Wouldn't that be just as good as laying down your product on my existing insulation ?
A. No.  One company claims their product performs better than other RB products and is not subjected to such problems as dust on the surface affecting its performance and claim their product would not trap moisture, where others products would. Because there is no regulation of what people say on web pages, the consumer is at the mercy of the advertiser. You need to demand that the seller provide you with acceptable test data on their product, not someone else's! You need to protect yourself so you don't get ripped off. Compare and don't be taken in by false claims. For example, all RB products installed in attics must have a flame spread rating of 25 or less according to UBC(Uniform Building Code). That means the supplier must be able to provide you with a copy of this test if you request it. When in doubt make them supply documentation!

Fact is, only RBS Chips have a lifetime, transferable performance warranty.  Before buying any RBS, make sure you get a performance warranty in writing.  As for the fire rating, RBS chips have a class III fire rating as specified on the material data safety sheet supplied by the manufacturer on MSDS (material safety data sheet).  This rating means RBS chips will burn but will not give off toxic fumes or smoke.  The main substrate is manufacuted by DuPont who also manufacturers, foam, plastic, wraps and other products for home use.  Here is an exerpt from the MSDS for our products:

FIRE FIGHTING MEASURES
----------------------------------------------------------------------
Flammable Properties
Films can be combusted only by remaining in contact with
flame.
If flame source is stationary, the film will shrink
away and self-extinguish.

 Keep this in mind: In a 2000 square foot home only 66lbs of RBS chips are used.  That's 1056 ounces spread out over 2000 square feet or a little over a half ounce per square foot.   There simply is not enough mass (fuel) to make this an issue.  To further prove this, in December of 2002 one of the homes that had RBS Chips installed had an attic fire due to a bad connection without an electrical box.  The old cellulose insulation caught fire and the homeowner observed this and put it out with a fire extinguisher.   When asked if the RBS Chips appeared to contribute the fire he replied "no".  

Is there a way to avoid dust in attics?
No. There is no practical way to keep an attic dust free so the challenge for radiant barriers is to work well in spite of the dust. As a matter of fact, a radiant barrier system is not designed to work with dust is not worth considering.  Some studies seem to be finding that some types of dusty radiant barrier are worse than no radiant barrier at all.

Well, then if the attic floor is the best place for radiant barrier but dust makes it not work, and it is difficult to install, what are my options?
These challenges were the catalyst to the invention of a new kind of radiant barrier called Radiant Barrier Chips (click here) . Chips are made from aluminized plastic film that is manufactured into small pieces. Then to install it, a lightweight blower and hose is employed to blow a coating of chips on top of the existing insulation. The radiant barrier becomes a topcoat to the insulation, the "icing on the cake" that makes a complete insulation.
Dust is no longer the death-knell because the chips are installed multiple layers deep, usually about 8 layers of protection. The layer exposed to dust becomes ineffective on the dusty side but all the rest keep doing their job.  Tim Carter, syndicated columinst and building expert has had RBS Chips in
his home for over a year.  Here's what he has to say about it: click here

Don't RBS Chips blow around from the wind?  
Soffit vents should have air chutes that direct wind up to the center of the attic and keep insulation from touching the roof.  If you don't have these you may consider adding them.

How about mixing the chips with the insulation and blowing them in all at once? Don't RBS Chips blow around from the wind?
Radiant barrier must have space between it and other materials or it doesn't work. Radiant heat travels through this space and without space, the heat is just conducted from the radiant barrier to the material touching it. The RBS Chip has a patented shape which overcomes these anomolies.

What happens if the chips are disturbed?
If the chips are installed on batt insulation, it is very easy to just move them back over the places where the insulation is exposed.  When chips are installed on loose-fill insulation and the chips become well mixed with the insulation, it is necessary to thin out the many layers around the disturbed area and use them to cover the exposed insulation.  One very good aspect of radiant barrier is that only the area that is not covered is adversely affected. All the rest of the areas continue to perform at the normal level. This characteristic is unlike insulation where if the batt was too small for the cavity it was installed in., it allows great convective air flow and almost makes the insulation useless.

Do the chips stop the moisture from migrating and cause condensation problems?
No. Because the chips are not one continous layer but are loose, the moisture trying to leave a warm humid house into a cold attic has no problem getting out. But with continous sheeting radiant barriers, moisture condensation has been a real problem in cold climates. RBS Chips are the only radaint barrier used successfully in cold climates.

What if the attic is small and there is no way a person could get in there to blow the chips?
Many times such attics are under-ventilated. With the need for more ventilation, this provides a serendipitous opportunity to cut venting holes in the roof, blow the chips in and then install attic dormer vents.  (See our venting page)

How about chips and cold climates?
Radiant Barrier Chips work as well in cold climates as it does in hot climates. Much like a Thermos bottle, the reflective coating on the RBS film reflects interior heat back into the room. Our testing has shown ceiling temperatures increase 8f to 10f degrees where the chips are installed. In new homes, radiant barrier can be installed in sheet form, just behind the drywall thus becoming a vapor barrier and a radiant barrier.

Phone Number: 602-867-3176